Rockford Fosgate R2-500X1 Prime mono subwoofer amplifier

Rockford Fosgate R2-500X1 Mono Amp: Setup, Wiring and Subwoofer Pairing

Quick answer: The Rockford Fosgate R2-500X1 is a Prime Series Class-D mono amplifier that delivers 500 watts RMS at 2 ohms, CEA-2006 certified. It is built to power one or two subwoofers wired to a 2 ohm final load, works with factory radios through speaker-level inputs, and includes a wired remote bass level control. Pair it with subwoofers totaling about 400 to 500 watts RMS.

A mono amplifier has one job: power subwoofers. The R2-500X1 does it with an efficient Class-D design, setup tools that make gain adjustment easier, and protection circuits that keep it safe. This guide explains the specs, which subwoofers match, how to wire it and how to tune it.

Key takeaways

  • 500 W RMS x 1 at 2 ohms, Class-D, CEA-2006 certified.
  • 20 Hz to 250 Hz frequency response, 80 A fuse rating.
  • Speaker-level and balanced differential inputs for factory or aftermarket radios.
  • CLEAN setup system for easier gain setting.
  • Variable Punch EQ, 12 dB/octave high-pass and low-pass filters, variable infrasonic filter.
  • Wired remote level control with 16 foot cable included.

Rockford Fosgate R2-500X1 specifications

Series Prime (R2)
Channels 1 (mono)
Amplifier class Class-D
RMS power 500 W x 1 at 2 ohms
Frequency response 20 Hz to 250 Hz
Fuse rating 80 A
Inputs Speaker-level and balanced differential (RCA)
Crossover 12 dB/octave Butterworth high-pass and low-pass, variable
Bass EQ Variable Punch EQ, variable infrasonic filter
Setup aids CLEAN setup system, Auto-Sense turn-on with bypass
Protection Short-circuit, over-current, thermal rollback
Remote Wired level control, 16 foot cable

What subwoofers match the R2-500X1?

Match the amplifier's 500 W RMS at 2 ohms to subwoofers whose combined RMS rating is roughly 400 to 500 W, wired to a final load of 2 ohms. Common ways to reach 2 ohms:

  • One dual 4 ohm voice coil (DVC) sub with the coils wired in parallel.
  • One single 2 ohm voice coil (SVC) sub.
  • Two single 4 ohm voice coil subs wired in parallel.

The amp also runs at 4 ohms with lower output, which suits a single 4 ohm sub rated for less power. For a 1 ohm subwoofer such as the T1S1-12, choose an amplifier rated for 1 ohm operation instead.

How does the R2-500X1 compare with the M2-500X1?

Spec R2-500X1 M2-500X1
Use Car and truck Marine and powersports
RMS power 500 W at 2 ohms 500 W at 2 ohms
Weather protection Standard Conformal-coated boards, UV-stable finish, marine-grade terminals
Remote Wired level control Remote Punch Level Control

For a car, the R2-500X1 is the better value. For a boat, UTV or open cab, choose the M2-500X1.

How to wire the R2-500X1

  1. Power: run power wire from the battery with a fuse within about 18 inches of the battery. A 4 gauge amp kit is a common choice for this amplifier; follow the manual for your run length.
  2. Ground: use a short ground wire, the same gauge as the power wire, bolted to bare chassis metal.
  3. Turn-on: connect the remote wire to the radio's amp turn-on lead, or use Auto-Sense with speaker-level inputs.
  4. Signal: connect RCA cables from an aftermarket radio, or use the included speaker input harness with a factory radio.
  5. Speakers: wire the subwoofer to reach a 2 ohm final load.
  6. Remote: mount the level control within reach of the driver and run the 16 foot cable to the amp.

If your vehicle keeps accessory power on after the ignition is off (Retained Accessory Power), use the Auto-Sense bypass switch as the manual describes.

How to set the gain and filters

  1. Turn the gain, Punch EQ and remote to minimum, and set the low-pass filter around 80 Hz.
  2. Set the infrasonic filter around 25 to 30 Hz to protect ported subs from very low frequencies.
  3. Play bass-heavy music with the radio at about three quarters volume.
  4. Use the CLEAN setup indicators as the manual describes to find the highest level before clipping, then turn the gain back slightly.
  5. Use the remote to adjust bass from the driver's seat, and add Punch EQ sparingly.

Video: Rockford Fosgate Prime amplifiers

Frequently asked questions

How many watts is the R2-500X1?

It delivers 500 watts RMS at 2 ohms on one channel, certified to the CEA-2006 standard.

Is the R2-500X1 1 ohm stable?

It is rated at 2 ohms. For a 1 ohm subwoofer, choose an amplifier rated for 1 ohm operation.

Can the R2-500X1 work with a factory radio?

Yes. Use the included speaker input harness and the Auto-Sense turn-on, so no line output converter is needed.

What size wiring kit do I need?

The amp uses an 80 A fuse rating. A 4 gauge kit covers most installs; check the manual for longer runs.

What does the remote level control do?

It adjusts subwoofer output from the driver's seat, so you can match bass to each song without opening the trunk.

What is CEA-2006?

A standard for measuring and rating amplifier power, so the 500 W RMS figure is a verified continuous rating, not a peak number.

Shop the R2-500X1

The Rockford Fosgate R2-500X1 is available now with 30-day returns. Compare more in mono subwoofer amplifiers, or ask our Tech Support team to match it to your subwoofer.

Specifications are from Rockford Fosgate's published data as listed on our product page. Written and reviewed by the CarAudioGarage Tech Support team, November 2026.