Rockford Fosgate R2-300X4: 4-Channel Amp Setup for Factory and Aftermarket Radios
Quick answer: The Rockford Fosgate R2-300X4 is a compact Prime Series 4-channel Class-D amplifier rated 75 watts RMS per channel at 2 ohms (300 W total). It powers four door speakers, connects to factory radios through speaker-level inputs, and can run all four channels from a front-only signal with its 2/4 channel input switch. It is a strong match for speakers rated about 50 to 80 W RMS.
Most radios, factory or aftermarket, make only about 15 to 20 watts RMS per channel. A 4-channel amplifier gives your speakers the clean power they need to play loud without distortion. The R2-300X4 is designed to make that upgrade easy, even if you keep the factory head unit.
Key takeaways
- 4 x 75 W RMS at 2 ohms, 300 W total, Class-D full range.
- 20 Hz to 20 kHz response, 60 A fuse rating.
- Speaker-level inputs and balanced differential inputs.
- 2/4 channel input switch and RCA pass-through outputs.
- CLEAN setup and independent front and rear gain controls.
- 12 dB/octave high-pass and low-pass filters.
Rockford Fosgate R2-300X4 specifications
| Series | Prime (R2) |
|---|---|
| Channels | 4 |
| Amplifier class | Class-D full range |
| RMS power | 75 W x 4 at 2 ohms (300 W total) |
| Frequency response | 20 Hz to 20 kHz |
| Fuse rating | 60 A |
| Inputs | Speaker-level and balanced differential (RCA), 2/4 channel switch |
| Outputs | RCA pass-through for system expansion |
| Crossover | 12 dB/octave Butterworth high-pass and low-pass |
| Setup aids | CLEAN setup, Auto-Sense turn-on with bypass |
| Protection | Short-circuit and over-current |
| Certifications | CEA-2006, CE |
What can the R2-300X4 power?
The most common setup is four door speakers: front left, front right, rear left and rear right. It also works with a front component set on two channels and rear coaxials on the other two. Good matches in our range include the R169X3 6x9s (65 W RMS), the P1V2-65 6.5 inch coaxials (75 W RMS) and the T1650-S components (80 W RMS). Most car speakers are 4 ohms, where the amp delivers less than its 2 ohm rating; check the manual for the 4 ohm and bridged figures.
How do you connect the R2-300X4 to a factory radio?
Use the two included 7 inch speaker input harnesses to take the signal from the factory speaker wires. The Auto-Sense feature turns the amp on when it detects a signal, so you do not need a remote turn-on wire. If your factory radio only has front speaker outputs, set the input switch to 2 channel and the amplifier will drive all four channels from that signal. If your vehicle keeps accessory power on after the ignition is off, use the Auto-Sense bypass as the manual describes.
How to install the R2-300X4
- Run power wire from the battery with a fuse within about 18 inches of the battery. A 4 or 8 gauge kit is typical for this amplifier; follow the manual for your run length.
- Ground it to bare chassis metal with a short wire of the same gauge.
- Connect the signal: RCA cables from an aftermarket radio, or the speaker input harnesses from a factory radio.
- Run speaker wire from each channel to each speaker, keeping polarity consistent.
- Use the RCA pass-through outputs to feed a mono subwoofer amp if you add one later.
How to set gains and crossovers
- Set both gains to minimum and the filters to high-pass at about 80 Hz.
- Play music with the radio at about three quarters volume.
- Use the CLEAN setup indicators to raise each gain until just before clipping, then back off slightly.
- Balance front and rear with the independent gain controls.
- If you have no subwoofer, you can lower the high-pass point for more mid bass, but keep it high enough to avoid distortion.
R2-300X4 vs R2-500X1: which amp do you need?
| Spec | R2-300X4 | R2-500X1 |
|---|---|---|
| Channels | 4 | 1 |
| Powers | Door speakers | Subwoofers |
| RMS power | 75 W x 4 at 2 ohms | 500 W x 1 at 2 ohms |
| Frequency response | 20 Hz to 20 kHz | 20 Hz to 250 Hz |
For a complete system, use both: the R2-300X4 for speakers and the R2-500X1 for a subwoofer.
Video: Rockford Fosgate Prime amplifiers
Frequently asked questions
Can the R2-300X4 work with a factory radio?
Yes. It has speaker-level inputs with two included input harnesses and Auto-Sense turn-on, so no line output converter is needed.
Can I power a subwoofer with the R2-300X4?
It is designed for full-range speakers. For a subwoofer, a mono amp such as the R2-500X1 gives far more bass power. Check the manual for bridged operation if you want to try a small sub.
How much power does the R2-300X4 make at 4 ohms?
Less than its 75 W x 4 rating at 2 ohms. Check the manual for the exact 4 ohm figure.
What does the 2/4 channel input switch do?
It lets the amp drive all four channels from a two-channel signal, which helps when your radio only has front outputs.
What size wiring kit does it need?
The amp uses a 60 A fuse rating. A 4 or 8 gauge kit suits most installs, depending on the length of the power run.
Shop the R2-300X4
The Rockford Fosgate R2-300X4 is available now with 30-day returns. Compare more in 4 channel car amplifiers, or ask our Tech Support team about connecting it to your radio.
Specifications are from Rockford Fosgate's published data as listed on our product page. Written and reviewed by the CarAudioGarage Tech Support team, November 2026.





